Painting Watch Tower from Iain Lovecrafts 'A Tale of Two Cities'

Published on by

Iain Lovecrafts 'A Tale of Two Cities' Painting the Watch Tower

Watch_Tower_Painting_10

Iain had recently asked if I could do a few test print and paints of some of the models that will be featuring in his new 'A Tale of Two Cities' Kickstarter.

The first model that I have finished is this handy little Watch Tower. It is a compact and functional building, just big enough for two Watch Men to survey the surrounding area. The model prints in four section, an upper and lower tower, door and roof. I printed my model on and Ender 5 using eSun PLA+ with a layer height of 0.2mm.

Watch_Tower_Painting_1Sandtex_Bitter_Chocolate

The first thing that I did was to give the whole model a good base coat of Sandtex - Bitter Chocolate. This is my favourite paint, I'm on to my second 5 Litre Can. I use it to base coat all of my figure bases, terrain boards and all model buildings and other terrain models. It bonds really well and gives a great smooth surface to work on.

Watch_Tower_Painting_3

After leaving the model for at least 12 hours so that the Sandtex in the deep recesses has completely dried, I made a start with the first of the three coats of drybrushing that I typically use on stone buildings.

Craft_Paints_and_Make_Up_Brushes

I use Acrylic Paint from 'Folk Paint' ranges for painting buildings, it is far more economical than model figure painting acrylic ranges. I always paint buildings (and drybrush miniatures) using Make Up brushes. Theses give fantastic results, they come in a wide range of sizes and shapes and have the perfect bristle for drybrushing. They are also a lot cheaper than model painting brushes. I brought the set that I am using now from Amazon, £10 for 16 brushes. I have been using them every day for the last 3 months and they are holding up well!

The first drybrush coat was a 50/50 mix of Nutmeg Brown and Khaki Tan. I squeezed a little of each colour onto an empty plastic lid, mixed together with brush, then wiped most of the paint off onto a kitchen towel and lightly drybrushed all over with large make up brush.

Watch_Tower_Painting_4

The acrylic drybrused paint dry's very quickly, so after 5 minutes I applied a second drybrush of 100% Khaki Tan.

Watch_Tower_Painting_5

After the second drybrush had dried, I used three different stone colours to pick out some individual stones to add interest. For these I did use model paints from Vallejo and Army Painter. The stone colours I used were Khaki Grey, Green Grey and Stone Grey.

Vallejo_Paints

I also painted any wood with 'Leather Brown' and the roof tiles with 'Dark Blue Grey'

Watch_Tower_Painting_6

To finish the model off I drybrushed and wooden areas with 'medium flesh' and then applied Army Painter Blue Tone Ink to roof and 'Strong Tone Ink to wooden areas.

All of the stone work was then given an overall light drybrush with 'Buttermilk' this is good to tone down and blend in the stones that were picked out in different colours and brings the whole model together.

The door was added. This is hinged. You can use PLA filament, but I preferred to use a length of Brass rod. I've added a rambling rose. This as an 'O' Gauge model railway accessory. A hole has been drilled in base to plant it and it has been glued down with superglue in a couple of places. I often like to add a plant or vines to stone models as a counterpoint to the strong straight lines.

The model was then given a couple of coats of Army Painter Matt Varnish to protect it.

Watch_Tower_Painting_8

The base of the tower, has some nice interior detail including a ladder.

Watch_Tower_Painting_9

The model roses were purchased from Model Scenery Supplies

The Miniatures shown in the photograph are from Sally 4th's Guards Guard range, available on Gamefound

Fantasy_square_640

The Watch Tower is part of Iain Lovecrafts 'A Tale of Two Cities'

Visit a Tale of Two Cities on Kickstarter

 

 

 

Classic view